What national cost guides say
HomeGuide (article dated July 30, 2025; page titled 2026) puts a complete 200-foot residential well at $6,000 to $16,000, with a national average of $10,500. That complete-install rate is $30 to $80+ per foot. Drilling only, without the rest of the system, is $20 to $30 per foot. HomeGuide’s published national bounds are a $3,000 minimum and $22,500 or more at the high end.
Angi (updated September 18, 2026) reports a national average of $5,500, with most homeowners paying $3,000 to $9,000, at $25 to $65 per foot. Angi says a deep system with wide steel casing can reach $24,500, and that rocky, sloped, or remote sites should be budgeted at $50 to $75 per foot. A drilled well’s starting cost on that page is $5,500, compared with $4,000 for a driven well and $2,500 for a dug well — the last two only where the water table is 50 feet or less.
The two guides are not pricing the same package. HomeGuide’s $10,500 average is described as including drilling, casing, pump installation, electrical connections, and permits. Angi tells readers separately to budget for permits, a pump, a pressure tank, and water testing, which helps explain why its $5,500 average sits lower.
| Source | What it measures | Published figures |
|---|---|---|
| HomeGuide, July 30, 2025 | Complete 200-foot residential well (drilling, casing, pump, electrical, permits) | $6,000–$16,000 typical; $10,500 average; $30–$80+/ft complete; $20–$30/ft drilling only |
| Angi, updated Sept. 18, 2026 | National average well-drilling cost; most homeowners’ range | $5,500 average; $3,000–$9,000 typical; $25–$65/ft |
HomeGuide costs by depth (national)
HomeGuide publishes complete-installation and drilling-only bands by depth. These are national ranges from that same July 30, 2025 article:
| Well depth | Complete installation | Drilling only |
|---|---|---|
| 100 feet | $3,000 – $8,000+ | $2,000 – $3,000 |
| 150 feet | $4,500 – $12,000+ | $3,000 – $4,500 |
| 200 feet | $6,000 – $16,000+ | $4,000 – $6,000 |
| 300 feet | $9,000 – $24,000+ | $6,000 – $9,000 |
Typical add-ons, also national
If a bid is drilling only, HomeGuide lists these common extras (same article): a well pump at $400–$2,500, a pressure tank at $800–$1,500, electrical wiring and connections at $1,000–$3,000, laboratory water testing at $100–$350, and a professional inspection at $250–$550. HomeGuide also cites well permits of $350–$700+ “depending on where you live.” That permit band is a national consumer-guide figure, not a Wisconsin fee schedule.
Official Wisconsin fees and rules
On its well and heat exchange notification page, the Wisconsin DNR states that the Well Construction Notification fee is $50.50. A heat-exchange notification has no fee. The fee and notification number are not refundable or transferable. A notification number must be obtained before construction starts, either at a DNR licensing sales location or through GoWild (an additional convenience fee applies to online purchases).
Wisconsin law requires advance notice before construction of a new private well that is not a high-capacity well. The DNR also states that wells must be constructed by a licensed water well driller, or a registered rig operator working under that license, with one exception: a property owner may drive or drill a well on their own property. After construction, a Well Construction Report must be submitted to the DNR within 30 days.
Counties and local health departments may charge their own permits or review fees on top of the $50.50 state notification. This site does not have a compiled county-by-county fee table, so no local permit amounts are shown here. Ask the driller, and the county, what applies to the property.
Why a Wisconsin bid can differ
Depth, diameter, and ground conditions are the usual drivers in the national guides — rock, slope, a deep water table, and a long run to the house all raise the price. Northern and central Wisconsin often mean drilling in igneous or metamorphic bedrock; other parts of the state have thicker sand and gravel. That geology is a reason to treat national per-foot averages as a starting point, not a quote. This guide does not invent a Wisconsin-only average on top of HomeGuide or Angi.
How to get a real number
- Ask at least two or three DNR-licensed drillers for written, itemized bids.
- Have each bid say whether the price is drilling only or a complete system (casing, pump, tank, electrical, testing, and permits).
- Confirm the Well Construction Notification and any county permit are included or listed separately.
- Check the license number against the official DNR roster before hiring.
Sources
- HomeGuide, “How Much Does Well Drilling Cost? (2026),” written by Tara Farmer, July 30, 2025. homeguide.com/costs/well-drilling-cost
- Angi, “How Much Does Well Drilling Cost? [2026 Data],” updated September 18, 2026. angi.com/articles/how-much-does-well-drilling-cost.htm
- Wisconsin Department of Natural Resources, “Well and heat exchange notification.” Official Well Construction Notification fee: $50.50. dnr.wisconsin.gov/topic/Wells/constructionNotification.html
Wells of Wisconsin is a private directory and is not affiliated with the Wisconsin Department of Natural Resources. Cost-guide figures belong to their publishers and can change. This page is not a bid or a promise of what any contractor will charge.